A pressure sensitive adhesive dispersion with very high shear strength, moderate tack and peel properties combined with excellent UV resistance. 5 750 -42 High Med Med UL181 duct sealing tape adhesive. Robond PS-60 acrylate latex was compounded with Rhoplex latex B-85, and Cab-o-sperse (a colloidal silica from Cabot Corp. ROBOND™ PS-6550 Adhesive is a versatile base polymer, adaptable to multiple end uses, Dow’s new ROBOND™ PS-2001NA acrylic pressure sensitive adhesive (PSA) enables the development of superior carton sealing tape. It is a rubber to substrate bonding system with more aggressive crosslinking chemistry to give good environmental resistance in the finished good. The adhesives are approved by FDA: FDA 21 CFR 175. DOWLEX™ 2045G Polyethylene Resin. A ready-to-use pressure sensitive aqueous acrylic emulsion for the manufacture of low noise polypropylene carton sealing tapes. Prior to adding the CR-3A Coreactant, use a mechanical mixer to stir the ROBOND L-188 Adhesive with enough speed until a vortex is formed, assuring that the adhesive is drawn from the sides and bottom of the mixing vessel. Sec. The principal uses for Robond™ L-330/CR 9-101 are to laminate a variety of. Instructions for Stabond Two-Part Adhesive for PVC & Hypalon Boats. RHOPLEX™ N-619 Water-Borne Adhesive. What is ROBOND™ L-300 Water-Borne Adhesive ? A two-component, VOC free and waterborne adhesive for laminating flexible substrates with high clarity, lower nip temperature and low foam. This will cause the adhesive to foam and make it difficult to apply. Adhesive system designed to be applied at high solids for a variety of applications including solvent-stable substrates and condiment packaging. What is ROBOND™ PS-8942 Water-Borne Adhesive ? A pressure sensitive acrylic emulsion for semi-permanent graphic application, ready to coat on reverse gravure coating lines. 2) Values shown are typical but may vary due to differences in vinyl or plasticizer. 5 150 -44 Med Med High Fast drying, good. Adhesives for UNDERHOOD and INDUSTRIAL Applications. What is ROBOND™ L-148 Water-Borne Adhesive ? A two-component, VOC free and waterborne adhesive for laminating flexible substrates with high clarity, lower nip temperature and low foam. 12 months from date of manufacture in unopened, original packaging. T. A clear, light amber, water-based, one-coat clear adhesive designed for bonding Fluoro-elastomers. Copy Link. Alcohol-free reduction, high clarity, and low foam are advantages of the system. 8 500 -50 Low Low High Minimal adhesion build, suitable for PVC and PET applications. Robond TR-5125(Dupont) A one-coat adhesive or as a cover-coat adhesive for use with THIXON waterborne or solvent-based primers. Adding to the show theme ‘Innovation Inspired by You’, Dow Adhesives has announced at Labelexpo Europe the latest innovation in its acrylic adhesives portfolio: ROBOND INVISU PS-7910 is specifically designed for self. Two Dow adhesive systems used for a broad range of polyethylene (PE) film packaging applications have been approved as compatible with mechanical recycling following a scientific evaluation by the non-profit,. 5% theoretical solids). 3% theoretical solids). Dow says the approval covers its solvent-free Morfree L 75-300/CR88-300 and water-borne Robond L350/CR-3 lamination adhesives, which will add an adhesive component to its Revoloop technology platform. ROBOND™ L-2152/Coreactant CR 9-101 adhesive provides high bond strength, excellent optical clarity, and strong heat and chemical resistance to a variety of applications. LLDPE designed for the production of a wide variety of industrial and consumer films with a unique combination of toughness, tear. Mixing. Once properly formulated it offers aggressive tack to a variety of surfaces including low surface energy materials. A permanent pressure-sensitive adhesive which is characterized by a balance of moderate shear strength and tack. We recommend that you make your own determination on the suitability of ROBOND PS 7880 Adhesive for your particular application. The procedure for how to remove adhesive from skin by using baby oil starts from here. 105 Adhesives and the applicable requirements of the Coalition of Northeast Governors' (CONEG) Standards on heavy metals. DOWLEX™ 2036P Polyethylene Resin. 105. These adhesives are subsequently dried after application to facilitate dry bond lamination. adhesive 55% solid water based robond 7500 emulsion: thailand: nhava sheva sea: kgs: 16,000: 2,134,938: 133: oct 03 2016: 35069999: 6010h water base adh 11-1260-1000-5 200kg/drum ( qty - 5 drums ) ( adhesive ) ( mfg use ) japan: bangalore: kgs: 1,000: 244,009: 244: sep 29 2016: 35069190: adhesive 55% solid water based robond 7500 emulsion:A - denotes Adhesive Failure, C - denotes Cohesive Failure FDA Status ROBOND™ PS-7874K and ROBOND PS-7874HV Adhesives comply with applicable requirements of FDA Food Additive Regulation 21CFR 175. It can also laminate a variety of other substrates including treated polyolefin and treated polyesters. The viscosity and excellent stability of ROBOND PS-94 Adhesive allow it to be used with aROBOND™ PS-2000 Adhesive is a permanent PSA which is characterized by excellent clarity and a balance of moderate shear strength and tack. Pressure sensitive and in-mold labels. ROBOND™ PS-8120 Adhesive Removable Pressure Sensitive Adhesive for Graphic and Film Labels Regional Product Availability Europe, Middle East and Africa Description ROBOND™ PS-8120 Adhesive is a pressure sensitive, aqueous dispersion polymer with a remarkable balance of quick stick, shear resistance, tack, and peel adhesion properties. It is also. Dow Chemical Company. It is intended for bonding Natural, SBR, Butyl, Nitrile, Polychloroprene and EPDM rubber compounds. This polymer emulsion has been designed with rheological properties which make it particularly suitable for transfer coating at low viscosity. What is ROBOND™ PS-8940 Water-Borne Adhesive ? A pressure sensitive aqueous dispersion polymer with a distinct balance of shear resistance, tack, and peel adhesion properties. Megum, Thixon and Robond adhesives are formulated to withstand a wide variety of conditions and extremely severe environments. When handling the product, do not generate excessive foam. 6. Prior to adding the CR 9101, use a mechanical mixer to stir the ROBOND™ - L-330 with enough speed until a vortex is formed, assuring that the adhesive is drawn from the sides and bottom of the mixing vessel. Alcohol-free reduction, high clarity, and low foam are advantages of the system. Formulation is particularly suitable slot die and comma coating methods. Description ROBONDTM PS-8915M Adhesive is a label and graphics adhesive which offers high tack while maintaining good plasticizer migration resistance and shrinkage. Slowly charge the Description ROBOND™ FD-07 Emulsion is a ready-to-use pressure sensitive aqueous acrylic emulsion for the manufacture of low noise polypropylene carton sealing tapes. However, the long-term shelf stability of silanes in the AS-1950-1 formulation is limited. Canada for over 20 years, Flexographic, Digital Label Print Shop. Adhesives may be weighed using a calibrated floor or benchtop balance at the proper ratio. Overview. 75 lb/ream, and cured for 5 days at room temperature, may be used as an adhesive layer in multilaminate food packaging materials with all food types with any food contact layer in full compliance with the Federal Food, Drug and Cosmetic Act. It is designed to seal to a vast range of substrates such as but not exclusive to, aluminum foil, cellophane, paper, PET, PVC, PE, and PP. Overview. –. Heat Seal Coating, Primer. Robond™ L-148 is designed for use as a two-component, VOC compliant, waterborne adhesive for laminating flexible substrates. The viscosity and stability of ROBOND™ PS-2020 Adhesive allows it to be used with a variety of direct coating methods. - Application coat weight approximately 19 g/m2 dry. Key benefits include no VOC from organic solvents, safer work-exposure, healthier food packaging, ease of use, and fast reprocessing with in-line slitting capabilities. ROBOND™ PS-2000 Water-Borne Adhesive. The family of ROBOND™ water-borne adhesives encompasses a broad portfolio of aqueous adhesives for pressure sensitive applications, sealing and laminating. New Robond PS 7845 adhesive is expected to be of special interest to label converters experiencing adhesion difficulties. Do not stir the adhesive so vigorously that air beaten in. These val ues should not be considered to be product specifications. The coating is typically applied to a flexible substrate, such as film, foil, paper, or non-woven material, and allowed to dry. High-performance adhesive formulations bond similar and dissimilar substrates in mounts, bushings, belts, brake pads, window profiles and other applications. What is ROBOND™ PS-8867 Water-Borne Adhesive ? A pressure sensitive aqueous dispersion polymer with a remarkable balance of cohesion, tack and peel adhesion properties for PE/PP film labels. 5% theoretical solids ApplicationTechnique. Users should confirm results by their own tests. The first step is to gently rub the area with a damp cloth. This adhesive has demonstrated excellent performance in both carton sealing film tape and overlaminate applications. This will cause the adhesive to foam and make it difficult to apply. ROBOND PS-9260 Adhesive is optimized for use on direct and reverse gravure coating heads. ROBOND™ L-148 is a two component water-based adhesive system used to make food packaging. In addition the high heat, chemical, and moisture resistance of ROBOND™ L-330 also make it a good adhesive for industrial applications. Continue to mix ROBOND™ TR-7115 while spraying or dipping to keep the dispersed solids from settling to the bottom. You can also use oil or petroleum jelly to. Alcohol-free reduction, high clarity, and good heat resistance are advantages of the Robond™ L-238 /CR-3A Coreactant adhesive system. This adhesive has demonstrated excellent performance in applications that require extreme clarity, for example clear-to-the-core OPP tape and overlaminate applications. 5 750 -42 High Med Med UL181 duct sealing tape adhesive. Performance results of ROBOND™ PS-8534 Adhesive Test conditions: - Transfer coated from Si release paper to 80 µ monomerically plasticized vinyl facestock. 0 8. 5 7. Alcohol-free reduction, high clarity, and low foam are important. A permanent PSA adhesive, which is characterized by excellent clarity and a balance of moderate shear strength and tack. Information provided by DuPont. Do not stir the adhesive so vigorously that air is beaten in. specialise in Resins, Fertilizers Chemicals,aluminum powder & paste,aluminum foil,potassium hydroxide and other industrial chemicals. An acrylic emulsion which may be used neat or as an adhesive formulating base. Adhesive system designed to be applied at high solids for a variety of applications including solvent-stable substrates and condiment packaging. Prior to adding the CR-3A Coreactant, use a mechanical mixer to stir the ROBOND L-188 Adhesive with enough speed until a vortex is formed, assuring that the adhesive is drawn from the sides and bottom of the mixing vessel. An emulsion or dispersion of the adhesive in an aqueous carrier liquid i Login Sign up. Waterborne solutions can meet or even exceed traditional solvent-based adhesive systems in terms of performance. Ready-to-Use Product Type: Waterborne Adhesive, 1K (1 component) Adhesive. Description THIXON™ 520-P-EF is a general purpose cover coat adhesive used for bonding rubber compounds to metals and other rigid substrates during vulcanization. A primer material. Add to list. It is optimized for use on direct and reverse gravure coating heads. 0 8. "Robond PS 7845 adhesive was designed to eliminate intermittent adhesion problems for papers containing higher concentrations of clay and calcium," said Sue Graham, global PSA marketing manager for Rohm and Haas Company. ROBOND™ adhesives, OPULUX™ optical finishes, and SURLYN™ ionomers were each recognized by APR for solving packaging design challenges. ROBOND PS-1067 Adhesive can be used with the crosslinker CR3, a dispersable. It removes cleanly from a variety of substrates (mainly. What is ROBOND™ PS-7860 Water-Borne Adhesive ? This high solids acrylic base polymer is designed for general purpose permanent label applications. Performance results of ROBOND™ PS-8534 Adhesive Test conditions: - Transfer coated from Si release paper to 80 µ monomerically plasticized vinyl facestock. It is designed for applications for which limited peel build is desired, such as re-sealable packaging constructions. Description ROBOND™ PS-9260 Adhesive is an acrylic emulsion polymer for pressure sensitive adhesive applications. Take baby oil in a small container. CuringROBOND L-90M Adhesive on PE films, a water-based, VOC-free adhesive used for laminating flexible substrates. 10. A pressure sensitive adhesive is disclosed that is tack-free to the touch, but forms a permanent bond under moderate pressure. 1. In other instances, a strong adhesive is required to permanently bond a metal part to the rubber, and a compounder will need a bonding product such as the Thixon or RoBond. Masking tapes prepared with ROBOND PS-9006 offer clean removability after aging on a variety of surfaces including glass and painted dry walls where 14 days clean removal is desired. A selection of Dow’s solvent-free and water-borne lamination adhesives have reportedly received approval for mechanical recycling from RecyClass and are now expected to contribute an adhesive component to Dow’s REVOLOOP technology platform. Overview. It is optimized for use on direct and reverse gravure coating heads. Barrier protection. to our brochure “ROBOND™ L-Series Acrylic Adhesives Pre-trial Guidelines” (form number 500-14701) Health and Safety Benefits •Acrylic emulsions are free of organic solvents (VOCs), offering you and your customer: –No retained solvents due to adhesive – Safer work environment – No solvent exposure due to adhesive1) ROBOND™ PS- 8915 Adhesive transfer coated from Si release paper to 80 μ monomerically plasticized vinyl facestock. This will cause the adhesive to foam and make it difficult to apply. 5 lbs/ream: 9H1H: 100:6. 105. DuPont Mobility and Materials Robond™ TR-7021-D Adhesive (Unverified Data**) Categories: Polymer; Adhesive; Thermoset. ROBOND™ L Waterborne Laminating Adhesives - North American Product Guide is a comprehensive pdf document that provides information on the features, benefits, applications, and technical data of various waterborne acrylic adhesives from Dow. Rohm and Haas Company (Rohm and Haas) has introduced new advanced, water-based acrylic polymer. Improved adhesion • Improved adhesive. 170. 4. Product name: ROBOND™ L-2150 Recommended use of the chemical and restrictions on use Identified uses: Packaging laminating adhesives COMPANY IDENTIFICATION THE DOW CHEMICAL COMPANY* Agent for Rohm and Haas Chemicals LLC 100 INDEPENDENCE MALL WEST PHILADELPHIA PA 19106-2399 UNITED STATES. Application coat weight approximately 19 g/m2 dry. Alcohol-free reduction, high clarity and low foam are important advantages of the ROBOND™ L-330/ CR 9-101 adhesive system. Stir ROBOND™ TR-5125 at approximately 50 RPM for 1 hour using the supplied drum mixer. Slowly charge the appropriate. The principal uses for Robond L-2150 adhesive with coreactant are in medium performance industrial laminations such as polyester film/scrim and polyester/foil for thermal insulation applications. Continue to mix ROBOND™ TR-7115 while spraying or dipping to keep the dispersed solids from settling to the bottom. Do not stir the adhesive so vigorously that air beaten in. 75 part diluent - estimate 14. The principal uses are to laminate a variety of substrates including. Measure the specific gravity using a Hydrometer or other instrument to assure the adhesive is properly mixed. AGILITY™ EC 7000 Performance LDPE. ROBOND™ PS-2000 Water-Borne Adhesive. It covers products such as ROBOND™ L-98D, L-90D, and FD-07, which are suitable for. Information provided. SurfacePrep Review Dow 's rubber-to-substrate bonding agent application guide or contact your account manager. Overview. 0 with Coreactant 9H1H - Industrial: Insulation Facing,Cable Wrap,General Industrial: High Heat Resistance,Adhesion to Foil and Metallized Films,High Chemical Resistance,High Bond Strength: ADCOTE™ 76P1-38: Solvent Based Adhesives Pressure Sensitive Adhesive Regional Product Availability Asia Pacific Description ROBOND PS-7022 is a waterborne, permanent pressure sensitive adhesive designed for general purpose permanent paper label applications. An acrylic emulsion which may be used neat or as an adhesive formulating base. Slowly charge theROBOND™ L-168 /CR-3A Coreactant adhesive system is usually applied as received. Add Property. Curing ROBOND L-90M Adhesive on PE films, a water-based, VOC-free adhesive used for laminating flexible substrates. Report. Description ROBOND™ FD -09 Adhesive is a ready -to -use pressure sensitive aqueous acrylic emulsion for the manufacture of low noise polypropylene carton sealing tapes. Dow Robond TR-7021-D is a 1-Part Heat cure, Waterborne-based, Liquid used to Bond NBR Compounds, CRS, and Aluminum. Tomato Ketchup, fabric, softener &etc. It is optimized for use on direct and reverse gravure coating heads. This polymer has good cohesive performance, compatibility with tackfiers and. We recommend that you make your own determination on the suitability of the ROBOND PS-7874 Adhesive Series for your. The main characteristics are: butene. Robond L-2150 adhesive provides optical clarity, high bond strength, and a high level of heat and chemical resistance. Adhesives and Sealants; Amines and Chelates; Conductive Materials; Elastomers and Plastomers; Foam Control Agents; Gels, Encapsulants and Conformal Coatings; Intermediates and Feedstocks; Lubricants, Heat Transfer and Deicing Fluids; Monomers; Optical Materials; Plastic Additives; Polyethylene; Polyurethanes; Release Coatings and. The approval covers solvent-free MOR-FREE™ L 75-300/ CR88-300 and water-borne ROBOND™ L-350/ CR-3 lamination adhesives 1, which will add an adhesive component to the REVOLOOP™ technology platform from Dow. What is ROBOND™ L-100 Water-Borne Adhesive ? A two-component, VOC free and waterborne adhesive for laminating flexible substrates with high clarity, lower nip temperature and low foam. A linear low density polyethylene that enables balanced tear and release properties processable at high line speeds in cast film. Based on Dow's novel patented advanced tubular technology, the resin is a high pressure homo low density polyethylene designed for good conversion efficiency and low gauges in extrusion coating or lamination processes running at speeds up to 300 m/min. The CR 9-101 coreactant must be used at the recommended mix ratio to achieve the desired adhesion and higher performance properties. Through water-based acrylic technology, Robond adhesives offer properties that are particularly important to Drupa's European converter attendees, who are challenged by increasing regulation and informed, highly aware consumers. Sold by Cipade S. Stir ROBOND™ TR-7115 before using to assure that the ingredients are uniformly distributed. 105 compliant and it adheres well to many packaging substrates including polyethylene,, polypropylene, PET, foil, and paper. ROBOND TR-100 can also be used as a one-coat adhesive for bonding some polar elastomers such as NBR or ACM. Slowly charge the appropriate. The adhesive also exhibits good. SHANGHAI, CHINA, October 23, 2007 – Rohm and Haas announced today that it has developed a new water-based acrylic adhesive, ROBOND™ Prohesion, designed for pressure sensitive tapes and other demanding applications traditionally served by solvent-based adhesives. Skin contact – Prolonged or repeated skin contact can cause slight irritation. It is also recommended for use in non-food applications where similar films and performance requirements apply. 4% theoretical solids 1 part adhesive: 0. APR’s Critical Guidance Recognition is a measure for assessing recyclability in plastics packaging design. What is ROBOND™ PS-68 Water-Borne Adhesive ? A coater-ready permanent pressure sensitive adhesive which is characterized by high peel adhesion and tack with adequate shear resistance. polyolefins, polyester, vinyl, aluminum foil, paper, metallized and PVDC-coated materials, the treated. Thixon 520-PEF Thixon 532-AEF Megum 5382 Thixon P6-EF / Thixon OSN-2-EFV RoBond TR 100 RoBond TR 5265 Thixon 2001-EF Thixon OSN-2-EF. In combination with CR 9-101, ROBOND™ L-148EU provides high clarity, low nip temperature, and low foam in laminating & converting operations. 0 8. +92-213-2567737 +92-300-9202867 F-61/H S. Robond™ L-100 is designed for use as either a one-component or a two-component, VOC compliant, waterborne adhesive for laminating flexible substrates. ROBOND™ PS-7735 Adhesive All Temp Adhesive Regional Product Availability North America Description ROBOND™ PS -7735 Adhesive is a ready to coat pressure sensitive adhesive for use in paper label and other applications requiring good adhesion at room temperature as well as refrigerator and freezer temperatures. The principal uses for Robond™ L-330/CR 9-101 are to laminate a variety of. This adhesive has aggressive peel and tack with moderate shear strenghth and superior cardboard adhesion with >85% fiber tear. It is supplied with "ready-to-coat" viscosity and rheology characteristics. 105. 1395 (for retort adhesive), and FDA 21 CFR 177. ROBOND FD-09 Adhesive is the result of many years of Dow experience in acrylic PSA technology. Peel adhesion (N/inch) Glass, 20 min dwell 9 Glass, 24 hrs dwell 14 Loop tack (N/inch 2) Glass 10,5 SPECIALTY ADHESIVES Bonding elastomeric materials to metal, engineering plastics or other elastomers requires a tough adhesive, like the customizable solutions offered by Dow Automotive Systems. . Measure the specific gravity using a Hydrometer or other instrument to assure the adhesive is properly mixed. THIXON, MEGUM, AND ROBOND rubber to substrate bonding systems from DuPont offer a robust bond in a wide variety of application environments, processing and cost advantages,. 8. 3% theoretical solids 1 part adhesive: 1. A permanent pressure sensitive adhesive which is characterized by a balance of moderate shear strength and tack. ROBONDTM PS-9260 Adhesive is an acrylic emulsion polymer for pressure sensitive adhesive applications. Diluents - Deionized or distilled water . ROBOND PS-1067 Adhesive can be used with the crosslinker CR3, a dispersable. Rohm and Haas Co. A permanent PSA adhesive, which is characterized by excellent clarity and a balance of moderate shear strength and tack. ROBOND™ TR-3295 is a waterborne-based one-coat adhesive for bonding fluorocarbon and acrylate compounds to metals and other solid materials under vulcanization conditions. A. Robond L-2150 is a waterborne, cross-linkable two component laminating adhesive that requires the use of a. Type. It is necessary that the CR 9-101 coreactant be added to the ROBOND™ L-330 adhesive with agitation. Alcohol-free reduction, high clarity, and low foam are advantages of the. ROBOND™ PS-8915M Water-Borne Adhesive. ROBOND™ PS-9181HV Adhesive Technical Data Sheet. RecyClass assessments follow rigorous scientific protocols to present a comprehensive evaluation of the. 7% theoretical solids 1 part adhesive: 0. An adhesive acrylic emulsion which may be used neat or as an adhesive formulating base. It is optimized for use on direct and reverse gravure coating heads. Closest Results from this Manufacturer. Place it over the sticky residue, and let it sit to dissolve the adhesive. This adhesive has demonstrated The Dow portfolio of adhesives and coatings offers many options and diverse performance attributes covering functionalities for many packaging applications: Retort processing. The approval covers solvent-free MOR-FREE L 75-300/ CR88-300 and water-borne ROBOND L-350/ CR-3 lamination adhesives, which will add an adhesive component to the REVOLOOP technology platform from Dow. It is also designed with an UV fluorescent brightener. Alcohol-free reduction, high clarity, good open time, and low. An acrylic emulsion polymer for pressure sensitive adhesive applications. Freezer-to-microwave convenience. Once properly formulated it offers aggressive tack to a variety of surfaces including low surface energy materials. Robond adhesives provide high shear strength that allows faster slitting to streamline the laminating process, thereby allowing converters to lower inventory and reduce delivery time to customers – key productivity advantages in the very competitive flexible packaging market, which is currently experiencing high customer cost pressures. The product exhibits characteristics and stamina never before seen or thought possible. Solvent-based coreactant used in combination with solvent-based adhesive systems in flexible packaging applications. RecyClass assessments follow rigorous scientific protocols to present a comprehensive evaluation of the. Ready-to-use aqueous Acrylic Pressure Sensitive Adhesive designed for use in aggressive tack and high shear strength tape applications. The coated substrate does not exhibit tackiness at room temperature and can be shipped to another destination for heat. Most commonly, ROBOND™ L-2152/Coreactant CR 9-101 is used to produce laminates for flexible packaging but may also be used for industrial laminations between materials like. It exhibits low peel build up overtime. An ethylene-butene copolymer designed for blown film applications. ROBOND™ PS-8120HV Removable Yes 54. LLDPE designed for the production of a wide variety of industrial and consumer films with a unique combination of toughness, tear. lve for bonding some polar elastomers such as NBR or ACM. This incredibly fast processing time coupled with a pot life of 8 hours allow for increased efficiency of water-based lamination. Meets grade d3. Mixing should be done in a round container using a mixing blade that is one-third of the container’s diameter. ROBOND™ L-148EU is a two component, VOC compliant, waterborne adhesive used for manufacturing multi-layer films made from flexible substrates. LLDPE designed for the production of a wide variety of industrial and consumer films with a unique combination of toughness, tear. ADCOTE™ 37R972 Water-Borne Heat Seal Coating. Do not stir the adhesive so vigorously that air is beaten in. DOWLEX™ 2045G Polyethylene Resin. 1) ROBOND™ PS- 8915 Adhesive transfer coated from Si release paper to 80 μ monomerically plasticized vinyl facestock. ROBOND L-90D is a ready-to-use, waterborne acrylic adhesive designed for use in the manufacture of flexible film laminates for food packaging. Solvent Based Adhesives: Gravure, Reverse roll, Smooth roll transfer: 43% - 1. This will assure that a homogenous mixture of the adhesive is applied. Solvent Based Adhesives: Gravure, Reverse roll, Smooth roll transfer: 43% - 1. A water-based system, based on natural rubber latex, developed for use in cold seal technology for flexible packaging applications. What is ROBOND™ PS-8120 Water-Borne Adhesive ? A pressure sensitive, aqueous dispersion polymer with a remarkable balance of quick stick, shear resistance, tack, and peel adhesion properties. Continue to mix ROBOND™ TR-7115 while spraying or dipping to keep the dispersed solids from settling to the bottom. Performance results of ROBOND™ PS-8534 Adhesive Test conditions: - Transfer coated from Si release paper to 80 µ monomerically plasticized vinyl facestock. A permanent PSA adhesive, which is characterized by excellent clarity and a balance of moderate shear strength and tack. The principal uses are to laminate a variety of substrates including polyolefins, nylon and polyesters. ROBOND™ is a line of water-based acrylic and urethane adhesives used for laminating a broad range of flexible substrates including films, foils, and paper. Bonding rubber to a variety of. The CR 9-101 coreactant must be used at the recommended mix ratio to achieve the desired higher performance properties. WeDuPont Kevlar is an organic fiber in the aromatic polyamide family. Do not stir the adhesive so vigorously that air is beaten in. Polyethylene resin designed for the production of a wide variety of industrial and consumer films offers good toughness and tear resistance . Adhesive designed for Painter’s Grade paper masking tape applications. ROBOND™ FD-07N Multiple Yes 60. This will cause the adhesive to foam and make it difficult to apply. An acrylic emulsion which may be. adhesion and higher performance properties. First, thoroughly mix/agitate ROBOND TR-100 with a propeller-type agitator. 5 750 -42 High Med Med UL181 duct sealing tape adhesive. ROBOND™ L-148. Dilute ROBOND™ TR-3010 with a ratio of 2 parts adhesive to 7 parts deionized water. ROBOND FD-07 Emulsion is the result of many years of Dow experience in acrylic PSA technology. 5 750 -42 High Med Med UL181 duct sealing tape adhesive. dwell time N/inch 5–6 AF Loop tack from stainless steel plates N/inch2 8–10 AF Shear resistance from stainless steel plates, 1"x1" – 1kg hrs. According to Midland, Michigan-based Dow, which has European headquarters in Horgen, Switzerland, RecyClass assessments follow rigorous. ADCOTE™ 89R3 34 225 15-20 MEK/Tol N/A N/A N/A Mounting adhesive for laminating solar control What is ROBOND™ L-90D Water-Borne Adhesive ? A single-component, ready to use, VOC compliant, waterborne acrylic adhesive for laminating flexible substrates in general performance applications. The main characteristics are: butene. We ROBOND™ PS-2000 Water-Borne Adhesive. ROBOND™ PS-8915M Water-Borne Adhesive. ROBOND™ Adhesives, OPULUX™ Optical Finishes and SURLYN™ Ionomers were each recognized by APR for solving packaging design challenges. Description ROBOND™ PS-6550 Adhesive has a distinct balance of peel adhesion, tack and shear resistance. It is waterborne acrylic pressure-sensitive adhesive designed for broad temperature, permanent paper label applications. Wide range of end use applications Technical expertise and support Full pilot coating capabilities to test your application needs Adhesion to high slip films,Good Clarity,Moisture Resistance,Long Pot life,Easy Clean-up,Low Nip Temperature,High Running Solids,Adhesion to Foil and Metallized Films,High Green Bonds,Fast Slitting Time,Low Odor,High Shear Resistance. Philadelphia, PA - Rohm and Haas announced recently that it has developed a new water-based acrylic adhesive, ROBOND Prohesion, designed for pressure sensitive tapes and other demanding applications traditionally served by solvent-based adhesives. 2 160-180 Optically clear solar control window film adhesive, used to laminate PET and met-PET films. 2), it is strongly recommended that the user verify that potential film property changes due to the lamination process and materials are acceptable for the end use performance requirements. It is supplied ready-to-use for transfer coating using a variety of machine configurations. Prior to adding the CR-3A Coreactant, use a mechanical mixer to stir the ROBOND L-168 Adhesive with enough speed until a vortex is formed; assuring that theRobond™ L-90M is designed for use as either a one-component or a two-component, VOC compliant, waterborne adhesive for laminating flexible substrates. Robond L-90M builds on the versatility of Robond L-90D to deliver improved shear strength, heat, and chemical resistance when combined with CR 9-101. OtherOctober 21, 2003. The approval covers solvent-free MOR-FREE™ L 75-300/ CR88-300 and waterborne ROBOND™ L-350/ CR-3 lamination adhesives, which will add an adhesive component to the REVOLOOP™ technology platform from Dow. The main characteristics are: butene linear low density polyethylene, blown film extrusion, and pellet form. This will cause the adhesive to foam and make it difficult to apply. . According to Rohm and Haas, ROBOND Prohesion is the first emulsion acrylic PSA to exhibit such impressive performance values in combination with high adhesion to a variety of substrates. This will cause turbidity (cloudiness) in the product. ROBOND™ PS-90 Water-Borne Adhesive. Key benefits include. Saturate a cotton ball with rubbing alcohol. 5. These tough adhesives offer high performance in severe environments while bonding engine mounts, bushings, seals and other anti-vibration parts. Laminating Adhesive Description Robond L-90M is designed for use as either a one-component or a two-component, VOC compliant, waterborne adhesive for laminating flexible substrates. OPULUX MC 5004 Coating on PE films, a water-based, low-gloss soft-touch coating that provides a matte appearance, excellent rub resistance and heat resistance when applied to a. We recommend that you make your own determination on the suitability of the ROBOND PS-7874 Adhesive Series for your particular application. Robond™ L-330 is designed for use as a two-component, VOC compliant, waterborne adhesive for laminating flexible substrates. Masking tapes prepared with ROBOND PS-9006 Adhesive offer clean removability after aging on a variety of surfaces including glass and painted dry walls where 14 days clean removal is desired. New from Rohm and Haas is the Robond™ Prohesion water-based acrylic adhesive, designed for p-s tapes and other demanding applications traditionally served by solvent-based adhesives. ROBOND™ Adhesives, OPULUX™ Optical Finishes and SURLYN™ Ionomers were each recognized by APR for solving packaging design challenges. RecyClass assessments follow rigorous scientific protocols to present a comprehensive evaluation of the recyclability of plastic packaging. ADHESIVES, INKS AND COATINGS BENEFITS •helps bridge the gap towards solvent-based formulation performance. Foil Foil, PE, itself 95 - 110 Oil & grease resistance, good hot tack, moisture resistanceDescription ROBOND™ PS-94 Adhesive is a permanent pressure sensitive adhesive which is characterized by a balance of moderate shear strength and tack. It is a coater ready system. . 5 7. Do not stir the adhesive so vigorously that air beaten in. Bonding elastomeric materials to metal, engineering plastics or other elastomers requires tough adhesives. 5 lbs/ream: 9H1H: 100:6. ROBOND™ L-148EU is a two component laminating adhesive that is used to manufacture flexible composite films for packaging applications. The new polymer contains Robond AquaBloc technology for the formulated adhesives that offers large improvements in water and high pH resistance in just such environments. Download PDF . Laminating Adhesive Description Robond L-90M is designed for use as either a one-component or a two-component, VOC compliant, waterborne adhesive for laminating flexible substrates. 2) Values shown are typical but may vary due to differences in vinyl or plasticizer. ROBOND PS-8915M Adhesive combines the water whitening resistance offered by other Dow adhesives such as ROBOND PS-8534 Adhesive along with the property of high tack provided by ROBOND 9631 Adhesive which end users in the graphics industry desire. The principal uses are to laminate a variety of substrates including. Application coat weight approximately 19 g/m2 dry. This adhesive has demonstrated excellent performance in both carton sealing film tape and overlaminate applications. Ideal for paper labels and an excellent option for e-commerce applications, INVISU™ 3400 adhesive offers many advantages. ROBOND™ L-148 is easy to mix and. This adhesive displays minimal adhesion build and clean removability. coreactant. A two-component water-based adhesive for laminating flexible packaging substrates in general or medium performance packaging applications. Product Guide Dow offers a broad line of water-borne dry bond laminating adhesives. . The coating is typically applied to a flexible substrate, such as film, foil, paper, or non-woven material, and allowed to dry. ROBOND™ PS-9650 Adhesive Pressure Sensitive Adhesive for Specialty Tapes Regional Product Availability • Europe, Middle East and Africa Description ROBOND™ PS-9650 Adhesive is an aqueous dispersion polymer for specialty tape applications that require high coating weights. MOR-FREE™ 569 Solventless Adhesives. ROBOND™ L-90M can be used on it's own as a one component adhesive, or it can be used in combination with Coreactant CR 9-101 as a two component system to. An acrylic emulsion polymer for pressure sensitive adhesive applications. RoBond™ TR-2525: DuPont: Waterborne Adhesive: RoBond TR-2525 is a one-coat bonding agent for bonding heat-curable silicone compounds to metal and other solid materials under vulcanization. Robond L-2150 adhesive adheres to a wide variety of substrates including cellophane, treated. ROBOND™ L-350 Water-Borne Adhesive DowIcon_Default_EventsAsset 105All Mitsui Chemicals’ polyurethane adhesives for flexible packaging are organo-tin compound free and bis-phenol A free. Once properly crosslinked is a versatile polymer that could be used in many protective. A permanent PSA adhesive, which is characterized by excellent clarity and a balance of moderate shear strength and tack. Alcohol-free reduction, high clarity, good open time, and low foam are important. ROBOND™ PS-90 Adhesive Pressure Sensitive Adhesive Regional Product Availability • Asia Pacific • Europe, Middle East and Africa • North America Description ROBOND™ PS-90 Adhesive is a permanent pressure-sensitive adhesive which is character-ized by a balance of moderate shear strength and tack. Key Features • Aggressive Tack Adhesive designed for Painter’s Grade paper masking tape applications. ROBOND™ L-90M: Water Based Adhesives: Gravure: 42 %: 45 cPs: 1. Open navigation menu. I. ROBOND™ FD-07 Adhesive Coating Weight g/m2 20 180° peel from stainless steel plates, 1 min. MEGUM™, THIXON™ and ROBOND™ bonding agents can be spe-cially formulated for. Solutions from Dow Automotive Systems MEGUM™/THIXON™/ROBOND™ Rubber-to-Substrate Bonding Agents Bonding elastomeric materials to metal, engineering p. DOWLEX™ 2036P Polyethylene Resin. Dow Chemical Company. The MOR-FREE L 75-300/ CR88-300 and ROBOND L-350/ CR-3 adhesives have. The viscosity and stability of ROBOND™ PS-2020 Adhesive allows it to be used with a variety of direct coating methods. A permanent pressure-sensitive adhesive which is characterized by a balance of moderate shear strength and tack. ROBOND™ PS-90 Water-Borne Adhesive. Viscosity. ) and coated on 24# bond paper. The principal uses are to laminate a variety of substrates including. Description ROBOND™ PS-9181HV Adhesive is a ready-to-use aqueous Acrylic Pressure Sensitive Adhesive designed for use in aggressive tack and high shear strength tape applications. Primer/cover-coat system that is the bench mark for glycol resistance at elevated temperatures. adhesive, excellent UV resistance. Close suggestions Search Search. Rohm and Haas has extended its line of environmentally advanced Robond™ adhesives with the addition of the new Robond PS-1000 series of aqueous acrylic p-s adhesives for protective applications. 5 750 -42 High Med Med UL181 duct sealing tape adhesive.